Installation Video Gluing Panel in Alcove

Fibo Wall Panels can be installed by gluing onto existing surfaces like Greenboard. Watch our video and see how easy you can get a perfect result in a short time. In addition to watch our videos, we recommend carefully reading the installation instructions to ensure proper installation according to certified standards.

You are now watching how to install Fibo by gluing directly onto Greenboard or similar, choose your preferred installation method below

Standard Panel – Alcove
Standard Panel Alcove – Gluing

Installing the base profile

  1. Make sure the shower tray is level, and that the walls are plum
  2. Measure the back wall and the return walls
  3. Cut base profile to size needed
  4. Apply sealant on the back of the base profile, leave a gap of 1/8 inch between tray and base profile.
  5. Attach base profile to the wall/studs behind existing surface by using screws

Installing the hidden corner profile

  1. Measure the height needed (start from the top of the base profile) and cut to size
  2. Make sure that the corner profile rest on top of the base profile and attach it to the wall using screws (the tape on the profile should be on the right hand-side when installing in the left corner)
  3. Right corner: Flip the profile so the tape is on the left-hand side

Installing the first panel

  1. Apply pencil marks to position the studs behind the existing surface (this is for adding a screw in top of the panel)
  2. Measure and cut the first panel
  3. Dry fit the panel, make sure it is plum, and leave a pencil mark on the right-hand side of the panel (so you will know where to put the glue)
  4. Apply glue and remove the protection cover for the tape
  5. Seal the cut edges on the panel. Rest the panel on the base profile and slide into corner until you hit the tap on the corner profile (make sure that the panel sits tight to the wall and is in the correct position before putting pressure on)
  6. Attach a screw in top of the panel which later will be covered by an L-shaped finishing profile

Installing the second panel

  1. Cut the panel to the required height
  2. Apply Fibo Seal in the click, and cut surfaces (not required on the top of the panel)
  3. Apply glue onto the wall (in pattern shown)
  4. Install the panel (important: Make sure that the Fibo Seal comes out of the joint on the whole panel)
  5. Remove excess sealant with: 1. Fibo Clean, 2. Fibo Sealing Tool, 3. Fibo Wipes

Installing the last panel on the back wall

  1. Measure between the laminate edge to the tap of the corner profile.
  2. Cut to size needed, and dry-fit before applying glue. (make sure it is plum)
  3. Apply sealant in the click and cut surfaces
  4. Apply glue and remove the protection cover for the tape
  5. Click the panel in place

Installing panel on return wall part 1

  1. Clean cut the first panel (the width) and cut to required height
  2. Dry fit, make sure it is plum and draw a pencil line to mark where to put the glue on the wall
  3. Apply sealant on cur surfaces
  4. Apply glue onto the wall, and push the panel in place. Push on the surface of the panel to make sure there is good contact to the glue behind
  5. Attach a screw in top of the panel which later will be covered by an L-shaped finishing profile

Installing panel on return wall part. 2

  1. Measure and cut to height and width required
  2. Apply sealant in click and on cut surfaces
  3. Apply glue to the wall
  4. Attach at least four screws approx. 1/4 inch from the edge facing out of the alcove (we recommend pre-drilling to gain the best result)

Sealing the internal corner

  1. Use Fibo Clean and Fibo Wipes to remove dust from the corners
  2. 1. Apply Fibo Seal in the corner, 2. Spray on Fibo Clean, 3. Remove excess with Fibo Sealing Tool

Sealing the tray/tub and the base profile

  1. Wrap the Fibo Sealing Tool in a Fibo Wipe cloth and remove dust between the gaps in the bottom
  2. Apply Fibo Seal between the bottom of the panel and the base profile. Remove excess with 1. Fibo Clean, 2. Fibo Sealing Tool.
  3. Repeat process between the tray/tub and the base profile

Installing the L-shaped finishing profiles

  1. Measure to sizes required and cut the L-profile (Miter the corners for the best result)
  2. Apply Fibo Seal to attach the profile to the edge of the panel
  3. Push the L-profile in place

Step 1 of

Fibo E-learning:

Learn how to install our Wall System and receive a diploma of certification!

Take the e-learning course

Find the correct accessories

The wall system is mounted by first setting up profiles that form the framework of the wall system. Then the boards are mounted, all joints are sealed with Fibo’s sealant, Fibo Seal. Accessories are also available to facilitate installation

Read more about the Fibo System

Some of the accessories you need

See all accessories
Corner profiles

Hidden internal corner profile

Don’t hesitate to get in touch!

Leave your note, and we’ll get back to you.

Customer services (US)

  • This field is for validation purposes and should be left unchanged.

Frequently asked questions

The Product will not delaminate, stain, fade or crack during the Warranty period as a result of defects in materials and manufacture of the Product, when properly installed in accordance with Fibo’s installation instructions and cared for in accordance with Fibo’s instructions for Cleaning and Maintenance or Product Guide, more details in Technical Data

Please note where the temperature is above 80°C/176°F eg. behind some gas stoves and
cooktops, we recommend using a heat resistant decorative material(stainless steel is commonly
used) or tempered glass product to protect the panel and avoid heat possibly dulling the
panel. Please check with the manufacturer of gas appliance to determine required wall clearance
for gas appliance installation to ensure temperatures don’t exceed the level listed above where
Fibo Kitchen Board is installed. Freestanding Ranges with a rear vertical control panel/display do
not apply to this concern.

Fibo can be used in most rooms, but there are exceptions. Like swimming pools and saunas. On the other hand, Fibo is excellent for changing rooms, showers and other spaces adjacent to saunas and swimming pools.

Yes, Fibo is approved for all wet room zones, for example, in the bathroom shower. This is due to the membrane in the sealing layer. Our panels are excellent in all wet rooms, but also where extra-durable walls are needed, like in hallways, garages or laundry rooms. Fibo Kitchen Board is built the same way and also waterproof.

Many of our panel models are delivered in 10-foot heights. If the model you choose cannot be found in the desired height, we have a list you can use to add the wanted height to Fibo. 

The most safe and versatile installation method is with the OSB strips. See how on this link.

If you plan to mount bathroom fittings, a washbasin, faucet, wall-mounted toilet or other bathroom furniture on the panel, you need to install, for example, a 0.5-inch thick sheet of plywood behind it. You can, of course, attach the decor to studs behind the wall. 

Fibo Seal is specially developed for our panels and is ETAG 022 approved. Fibo Seal is also supplied in the same colors as the joints on the panels. Do not use silicone, only MS polymer sealant approved according to SINTEF TG 2289.

Use the Purchase calculator to find out what’s necessary for your installation. If you need more guidance please contact your supplier of Fibo panels, or Fibo directly at info@fibosystemusa.com.

For installation on masonry/concrete walls above ground, use the following solution: Make sure the concrete is dried out and has a maximum moisture level of 85% when mounting. The substrate must be level and provide good attachment possibilities for nails and screws where the panels meet. Remember, where you hang up washbasins or other heavy objects, there must be extra reinforcement.

Forget about the vapor barrier, primer, fix and joints. Fibo panels have an integrated vapor barrier and you can mount the panels directly on the wall framework.

Yes, Fibo can be glued onto old existing tiles. Ask a craftsman or a hardware store for the most suitable glue. You can view the complete installation guide at this link.

Yes, it is safe to glue Fibo onto drywall, however check the suppliers requirements for extra support before installing a seat, niche or grab bar.

Close